CANStepper NEMA 23: closed-loop stepper driver with CAN FD
A 56.6 mm square driver board that bolts to the back of a NEMA 23 motor. It runs the motor open loop from any STEP/DIR controller, or closed loop from its own STM32 and on-axis magnetic encoder, networked over CAN FD.
- Bolts to the back of a NEMA 23 motor (56.6 × 56.6 mm board)
- Open loop from any STEP/DIR controller, or closed loop over CAN FD or USB-C
- Trinamic TMC5160A with 8 × 100 V external MOSFETs, up to 3.1 A RMS / 4.4 A peak
- 14-bit MT6701 magnetic encoder on the motor axis (16,384 counts/rev, 0.022°)
- STM32H503 Arm Cortex-M33 controller, up to 250 MHz
- CAN FD up to 8 Mbit/s with switchable 120 Ω termination and daisy-chain connectors
- Two limit / home inputs (3.3 V switch or sensor, and 12 V NPN proximity sensor)
- Reverse-polarity, surge and fuse protection on the 24–48 V input
Applications
Makes a NEMA 23 stepper motor a networked closed-loop axis.
CANStepper NEMA 23 (CANStepper V1.0) is a 56.6 mm square driver board that bolts to the back of a NEMA 23 motor. It runs the motor open loop from any STEP/DIR controller, or closed loop from its own STM32 and on-axis magnetic encoder, networked over CAN FD.
Status: prototype, hardware rev V9. Specifications below are from the current design and may change before launch. Continuous current rating is still to be confirmed in thermal testing.
Two ways to run it
Mode A · SDMODE switch on · Open loop, STEP/DIR. Connect STEP, DIR and GND from a CNC, 3D-printer or PLC controller. The TMC5160 drives the motor directly from those pulses, with up to 256 microsteps and StealthChop2 quiet operation. DIAG0 is returned on the same connector for fault or stall signalling.
Mode B · SDMODE switch off · Closed loop, CAN FD or USB. The STM32 commands the TMC5160 over SPI and reads the motor angle from the MT6701 encoder, so it can correct lost steps and report real position. Commands and status travel over CAN FD (daisy-chained boards) or USB-C.
Power
| Item | Specification |
|---|---|
| Input voltage | 24–48 V DC nominal. Starts at about 16.5 V (undervoltage lockout). 48 V maximum continuous. |
| Input fuse | 6.3 A, on board |
| On-board rails | 12 V buck (LM5164, 1 A) · 3.3 V buck (TPS562201, 2 A) |
| Daisy chain | Two identical power + CAN connectors in parallel. 5 A per contact (connector rating). |
| USB power | Not used: USB-C carries data only, the board runs from the main input |
| Input monitoring | Supply voltage measured by the MCU |
Motor driver
| Item | Specification |
|---|---|
| Driver | Trinamic TMC5160A with external MOSFET bridges |
| Power stage | 8 × CSD19537Q3, 100 V N-channel MOSFETs |
| Motor | 2-phase bipolar stepper, NEMA 23, 4-wire |
| Coil current | Up to 3.1 A RMS / 4.4 A peak, set in software. Limit set by 75 mΩ sense resistors. Continuous rating to be confirmed in thermal testing. |
| Microstepping | Up to 256 microsteps (MicroPlyer interpolation) |
| Features | StealthChop2, SpreadCycle, StallGuard2, CoolStep, built-in ramp generator |
Controller
| Item | Specification |
|---|---|
| MCU | STM32H503CBT6, Arm Cortex-M33 up to 250 MHz. 128 KB flash, 32 KB RAM, 24 MHz crystal. |
| Firmware loading | USB-C bootloader (BOOT button) or SWD pads |
| Debug pads | 3V3 · SWCLK · SWDIO · GND · NRST |
| Controls | RESET and BOOT buttons · mode switch (SDMODE) · CAN termination switch |
| Indicators | Power LED · status / error LED |
Position feedback
| Item | Specification |
|---|---|
| Encoder | MT6701 magnetic angle sensor, 14-bit (16,384 counts/rev) |
| Interface | SSI to the MCU, with field-strength status |
| Location | Underside of the board, centred on the motor axis |
| Magnet | Diametric NdFeB, Ø6 × 2.5 mm or Ø8 × 3 mm, on the rear shaft. 1–2 mm air gap to the sensor, centred within 0.3 mm. Needs a dual-shaft motor. |
Communication and inputs
| Item | Specification |
|---|---|
| CAN FD | TI TCAN3413, up to 8 Mbit/s |
| Termination | 120 Ω, switchable on board |
| USB | USB 2.0 Full Speed device, USB-C, ESD protected |
| STEP / DIR | 3.3 V logic level. Not 5 V tolerant: use 3.3 V signals or a level shifter. |
| Limit / home 1 | Switch or 3.3 V sensor (connector supplies 3.3 V) |
| Limit / home 2 | NPN proximity sensor (connector supplies 12 V) |
Protection
| Item | Specification |
|---|---|
| Input | Reverse-polarity P-MOSFET (100 V) · 48 V TVS surge clamp · 6.3 A fuse |
| Driver | Short-circuit and over-temperature shutdown, fault lines to the MCU |
| Interfaces | USB ESD protection · bus-fault-protected CAN transceiver |
Mechanical
| Item | Specification |
|---|---|
| Board size | 56.6 × 56.6 mm (NEMA 23 frame is 56.4 mm) |
| PCB | 6 layers |
| Mounting | 8 × Ø3.3 mm plated holes for M3, at (±24.25, ±15.00) and (±15.00, ±24.25) mm from the motor axis, on a Ø57.0 mm circle. |
| Tallest part | About 14.5 mm (100 µF electrolytic capacitors, top side) |
| Underside | Only the encoder IC, facing the motor |
Frequently Asked Questions
When can I buy CANStepper NEMA 23?+
It is a prototype (hardware rev V9) and is not on sale yet. Join the waitlist on this page and we will email you when units, pricing and lead times are confirmed. Joining the waitlist is free and takes no payment.
Can I use it with my CNC or 3D-printer controller?+
Yes. With the SDMODE switch on, the TMC5160 runs open loop from STEP, DIR and GND signals. The STEP/DIR inputs are 3.3 V logic and not 5 V tolerant, so use 3.3 V signals or a level shifter.
Which NEMA 23 motors does it fit?+
2-phase bipolar, 4-wire NEMA 23 steppers up to 3.1 A RMS / 4.4 A peak. For closed loop, the motor needs a rear shaft (dual-shaft motor) to carry the diametric encoder magnet.
How is it different from the NEMA 17 CANStepper?+
The NEMA 23 board runs at 24–48 V with a TMC5160A and external MOSFETs (up to 3.1 A RMS), uses an STM32H503 and CAN FD up to 8 Mbit/s, and adds a STEP/DIR mode. The NEMA 17 CANStepper uses a TMC2209, ESP32-C3 and classic CAN at 5–24 V.
